You are searching about Al And F Express Your Answer As A Chemical Formula, today we will share with you article about Al And F Express Your Answer As A Chemical Formula was compiled and edited by our team from many sources on the internet. Hope this article on the topic Al And F Express Your Answer As A Chemical Formula is useful to you.
All About Vacutainer Tubes
Historically, Vacutainer tubes in glass were invented by Joseph Kleiner in 1947. They are being manufactured and marketed by BD (Becton, Dickinson and Company) since 1949. Vacutainer is a registered trademark of Becton, Dickinson and Company. The plastic version, known as Vacutainer PLUS, was developed at Becton Dickinson Research Center, RTP, NC during 1991-1993, by co-inventors E. Vogler, D. Montgomery and G. Harper.
The first evacuated tube invented by Joseph Kleiner was called Evacutainer. BD hired Kleiner as a consultant for the product and changed the name of his tube to Vacutainer®.
Prior to the invention of an evacuated tube system, before collecting blood, solutions for the additive tubes like EDTA and citrate were prepared and dispensed into test tubes for blood anticoagulation. Then, to identify the proper draw volume, the laboratory used to etch lines in the borosilicate glass tubes. The phlebotomist would collect blood specimens with needles and glass syringes. After collection, the blood would be transferred into a series of test tubes and sealed the tubes with black rubber stoppers for transportation of the specimens to the laboratory. For electrolyte measurements, mineral oil was added to the tubes to prevent loss of CO2. For serum specimens, wooden applicator sticks were used to loosen the clot from the tube walls (Franklin Lakes, 1996).
The shortcomings of these techniques were numerous. The patients were subjected to the ordeal of multiple needle entries to the vein. The errors during the collection and transfer process and the safety risks were unavoidable (Franklin Lakes, 1996).
The introduction of vacuum blood collection systems marked an era of greater safety, easy handling, speed, and accuracy in blood-to-additive ratios. During blood collection with evacuated tubes, one end of the needle entered the patient’s vein; the other end penetrated the rubber stopper as the tube was pushed into the open end of the holder. The vacuum enabled the tube to fill with the appropriate volume of blood.
Initially vacutainer tubes were packaged and shipped in vacuum tins similar to coffee cans. This was a breakthrough at the time because previously, a heavy clamp was used to prevent the stoppers from popping off during autoclaving (Franklin Lakes, 1996). However, now there are regulatory agencies and guidelines that ensure the consistency in the design and manufacture of blood collection systems like Food and Drug Administration (FDA); International Standardization Organization (ISO); and Clinical Laboratory Standards Institute (CLSI); The Medical Device Amendment (1976) and the Safe Medical Devices Act (1990).
A Vacutainer tube and the apparatus consists of a plastic hub, a hypodermic needle and a vacuum tube. Vacutainer tubes also contain additives to stabilize and preserve the blood specimens prior to analysis. Vacutainers are available with a wide range of labeling options and closure colors. They are also available with a range of draw volumes with or without a safety-engineered closure.
Vacutainer tubes have found wide recognition due to their functional ease. The venipuncture protocol employing a syringe requires elaborate preparations for blood sample analysis in terms of addition of appropriate additives into the tubes that carries more risks of sampling and analytical errors.
Vacutainer tubes have a color-coded plastic cap. The color code of the caps indicates the blood additives the tube contains. Additives are chemical substances that preserve the blood for processing in the laboratory.
The additives include anticoagulants like EDTA, Sodium citrate and Heparin. Some vacutainer tubes have a gel that has an intermediate density between blood cells and the serum. During centrifugation of these gel containing tubes, the blood cells sink to the bottom of the tube and are covered by a layer of the gel leaving the serum on top. When plasma containing blood platelets is required for analysis a vacutainer that does not contain gel or a clotting agent is used and centrifuged. The color code has a standard protocol and hence, finds universal application across the medical domain.
The Order of Draw:
As mentioned earlier, vacutainer tubes facilitate multiple blood suctions and the needle that pierces multiple tubes may carry additives from one tube into the next that hamper the blood analysis. Hence, there is need for a standardized sequence for such multiple suctions to avoid cross-contamination of additives. The Order of Draw is a term that refers to a standard protocol that has been developed for the sequence in which these tubes should be filled.
Recent Trends and Recommendations:
Recent trends in vacutainers include tubes made up of polyethylene terephthalate and use of various types of blood collection needles. Vacutainer tubes of recent introduction are made of a special formulation of the plastic, polyethylene terephthalate that is extremely strong, dimensionally stable, and resistant to chemicals and breakage. The manufacturers specify that all non-gel blood collection tubes, including those that contain heparin, EDTA and non-gel serum tubes can be centrifuged at ≤1300 RCF for 10 minutes. There are also tubes that should be spun at room temperature at a speed of 1000 to 1300 RCF for 10 minutes in a swinging bucket centrifuge and 15 minutes in a fixed-angle centrifuge.
These recent tubes are coated with silicone and micronized silica particles to accelerate clotting. A silicone coating reduces adherence of red cells to tube walls. The silica coating can sometimes cause the inner tube wall to appear cloudy and/or filmy. This cloudy appearance does not make the tubes unacceptable for use. Most Tubes are packaged 100 tubes/box and 1,000 tubes/case (10 boxes). The expiration date on the tube label is stated as a month and year. The tubes expire at the end of the month that is stated on the label. Vacutainer blood collection tubes have a sterile interior. Tubes are sterilized by gamma radiation (Wayman, 1994).
These tubes are under a specific negative pressure. During the re-sterilization cycle this negative pressure may be disrupted and therefore the tubes may not draw the proper blood volume. Thus, these tubes are sterile on the interior only. The manufacturer does not recommend re-sterilizing the tubes with ethylene oxide or autoclaving, due to pressure changes that take place during the re-sterilization cycle. Some manufacturers do offer a sterile peel-apart pouch that contains a 10 mL glass red top serum tube and 7 mL glass lavender top EDTA tube. 3mL and 6mL plain tubes with no added additives used as discard tubes are also available and find utility when drawing blood directly from an indwelling line or catheter. The tubes should be stored at 4-25’C (39-77’F) and requires inversions after a draw. An inversion is one complete turn of the wrist, 180 degrees, and back.
Tubes should be inverted according to the following recommendations of the manufacturer:
SST and serum tubes – 5 inversions
Additive tubes (EDTA, heparin, etc) – 8-10 inversions
Sodium citrate tubes (blue top) – 3-4 inversions
The market is recently flooded with vacutainer tubes that contain a closure that has a unique rubber stopper. It is recessed within and covered by a plastic shield to help protect laboratory personnel from contact with blood on the stopper or around the outer rim of the tube. The tube closure also helps prevent blood from splattering when the tube is opened.
Vacutainers containing a gel that forms a physical barrier between serum or plasma and blood cells during centrifugation has been introduced. It is recommended that after blood collection, Serum Separation Tubes should be inverted five times, allowed 30 minutes clotting time, and centrifuged for 10 minutes at 1000-1300 RCF (g) in a swing bucket centrifuge. Plasma Separation Tubes and should be inverted 8 times, and centrifuged for 10 minutes at 1000-1300 RCF (g) in a swing bucket centrifuge.
The gel is composed of inert components, which are part of a polyester-based proprietary formulation. The silica particles that coat the walls of the tube are actually the clot activators. Initial activation occurs when blood enters the tube and contacts the particles on the tube wall. To continue the activation process, it is necessary to thoroughly mix the blood and particles by inverting the tube five times.
The coating process creates a film on the tube surface that appears white and slightly cloudy. The tubes are fine to use. However, it is important to remember to invert the SST™ Tube at least five times after filling. This ensures adequate mixing of silica particles with the blood, which is required for optimal performance.
Serum Separation Transport Tube are tubes that contain double the amount of gel compared to the regular tubes. This provides a thick barrier that remains intact when tubes are transported, thereby maintaining the quality of the sample for the lab analysis. It is intended for use primarily when specimens are collected and centrifuged in physician laboratories or other remote collection stations, and then transported back to the laboratory for analysis.
Gel separation tubes should be centrifuged no longer than 2 hours after collection. The manufacturers do not recommend re-centrifuging gel tubes once the barrier has formed. It is not recommended to freeze the sample in the primary blood collection tube, on the gel barrier. The gel may separate when it is frozen and thawed, resulting in red cell contamination of the sample. It is not recommended to use the gel tubes for any tri-cyclic antidepressant drug testing and has not been validated for trace element testing. It is recommended to use the royal blue stoppered trace element tubes for trace element testing.
EDTA Vacuum (Vacutainer)Tubes
EDTA stands for Ethylenediaminetetraacetic acid. EDTA functions by binding calcium in the blood and keeping the blood from clotting. The nominal EDTA concentration is 1.8mg EDTA per milliliter of blood. Most recent Blood Collection Tubes contain K2EDTA, which is spray-dried to the walls of the tube. K2EDTA is recommended by the CLSI (CLSI guideline – Evacuated Tubes and Additives for Blood Specimen Collection-Fifth Edition H1-A5, 2003) and the ICSH (International Council for Standardization in Hematology).
Glass blood collection tubes contain K3EDTA, the liquid form of EDTA. K3EDTA is a liquid and will dilute the sample ~ 1-2%. K2EDTA is spray-dried on the walls of the tube and will not dilute the sample. K2EDTA Tubes are intended for routine immunohematology testing, including red cell grouping, Rh typing and antibody screening. The minimum and maximum acceptable blood volumes should be established by each facility, to ensure that accurate hematology results are obtained. Blood Collection Tubes are designed to draw the appropriate volume to ensure a proper blood to additive ratio (Antignani et.al, 2001).
Sodium Citrate Tubes
Sodium citrate tubes are designed to yield within ± 10% of the stated draw volume on the label of the additive tube throughout the entire shelf life. CLSI recommends that sodium citrate tubes be spun at 1500 RCF for 15 minutes to achieve platelet poor plasma (platelet count < 10, 000) and accurate coagulation test results. The etched fill indicator on the plastic citrate tubes indicates the minimum acceptable blood volume in the tube. Automated instruments require an average of 100 µl per test for PT and APTT, 50 µl for Fibrinogen, and 20 µl for Factor Assays.
There have been recent research articles indicating that drawing a discard tube is not necessary before drawing the sodium citrate tube. In the CLSI coagulation document (H21-A5) it is still recommended that the citrate tube is the second or third tube drawn. However, in the CLSI guideline for Venipuncture Collection (H3-A6) it states that for routine PT and APTT, the first tube drawn may be used for testing. It is also important to ensure a discard tube is drawn when a blood collection set is used and only a citrate tube is ordered, as the tubing may contain up to 0.5 mL of air that will be drawn into the tube and displace blood volume. The 1.8 mL tube has a light blue rubber stopper covered with a translucent shield and the 2.7 mL tube has a light blue rubber stopper covered with a solid light blue closure.
Heparin is derived from porcine intestinal mucosa. The green top heparin tubes contain either the lithium or sodium salt of the heparin anticoagulant. Lithium heparin should not be used for lithium determinations. All of the heparin is spray-dried on the wall of the tube. Prior to April 1, 2010, the heparin concentration has been approximately 15 USP units of heparin per milliliter of blood. The USP is not equivalent to the International Units (IU). The IU is 6.4% greater than the USP. As of April 1, 2010, if a sodium or lithium heparin tube has a capital N superscript alphabetic character following the word Heparin (i.e.HeparinN), the USP and IU are equivalent. A numerical change in the number of USP Activity Units as a result of the harmonization to the WHO International Standard is displayed. When the Sodium Heparin tubes are filled to the proper volume, the sodium results will only be 1 to 2 mmol/ mL higher (Bush et.al, 1998).
Trace Element/ Lead Tubes
Blood Collection Tubes can be used for monitoring Antimony, Arsenic, Cadmium, Calcium, Chromium, Copper, Iron, Lead, Magnesium, Manganese and Zinc. The manufacturer offers trace element tubes with two different additives. The plastic tube contains silica particles and can be used for serum analysis. The plastic trace element tube with K2EDTA, can be used for whole blood or plasma analysis (Bush et.al, 1998).
SPS tubes are used for blood culture specimen collection in microbiology. Eight gentle tube inversions are recommended to prevent blood clotting. The blood can remain in the SPS tube for two to four hours before it being transferred to a blood culture bottle.
Blood Collection Kits
Push Button Blood Collection Sets and Safety Winged Blood Collection Sets are more recent innovations in the market. The Push Button Blood Collection Set and the Safety Blood Collection Set can be used with a syringe when it is used without a luer adapter. The syringe will attach to the female end of the Push Button Blood Collection Set or the Blood Collection Set. Once the blood has been drawn into the syringe, the safety mechanism on the winged needle set is properly activated. The use of any needle for the purpose of transferring blood directly from a syringe to a specimen container continues to be prohibited by Federal OSHA. The syringe should be attached to a device, such as Blood Transfer Device, that meets all procedural and safety standards for blood transfer. It is critical to purge the air from the tubing of a blood collection set when collecting a sodium citrate tube for PT and/or APTT testing. A plain discard tube or another sodium citrate tube should be used first to purge the air from the tubing and allow a full draw into the citrate tube. Purging the air from the tubing is also recommended before drawing any additive tube. CLSI recommends that all additive tubes should be filled to their stated volume. The PBBCS and SLBCS are available in 21, 23 and 25 gauge needles (Bush et.al, 1998).
Vacutainer tubes are simple, easy to use, and safety-engineered. The safety mechanisms after the blood draw helps protect against needlestick injury. The tubes are also offered with a pre-attached holder for added convenience and to help ensure OSHA single-use holder compliance.
Adcock, DM, Kressin DC, Marlar RA. Effect of 3.2% vs 3.8% sodium citrate concentration on routine coagulation testing. Am J Clin Path. 1997; 107:105-110.
Antignani A, Cheng E, Evans J, Grippi, et al. ‘Method of using additive formulation and method for making tube with an additive formulation’, U.S. Patent No. 6,187,553, February 2001.
Becton Dickinson and Company. Joseph Kleiner and the origins of the Vacutainer™. The Echo. Becton Dickinson and Company, Franklin Lakes, NJ: 1991 (Spring);11:3-5, 1991(September);11:5-7; 1996(December);16:1
Tubes are sterilized by gamma radiation (Wayman, 1994).
Video about Al And F Express Your Answer As A Chemical Formula
You can see more content about Al And F Express Your Answer As A Chemical Formula on our youtube channel: Click Here
Question about Al And F Express Your Answer As A Chemical Formula
If you have any questions about Al And F Express Your Answer As A Chemical Formula, please let us know, all your questions or suggestions will help us improve in the following articles!
The article Al And F Express Your Answer As A Chemical Formula was compiled by me and my team from many sources. If you find the article Al And F Express Your Answer As A Chemical Formula helpful to you, please support the team Like or Share!
Rate Articles Al And F Express Your Answer As A Chemical Formula
Rate: 4-5 stars
Search keywords Al And F Express Your Answer As A Chemical Formula
Al And F Express Your Answer As A Chemical Formula
way Al And F Express Your Answer As A Chemical Formula
tutorial Al And F Express Your Answer As A Chemical Formula
Al And F Express Your Answer As A Chemical Formula free