You are searching about *What Is The Formula For Surface Area Of A Cylinder*, today we will share with you article about What Is The Formula For Surface Area Of A Cylinder was compiled and edited by our team from many sources on the internet. Hope this article on the topic **What Is The Formula For Surface Area Of A Cylinder** is useful to you.

Muc lục nội dung

- 4 Ways to Minimize Hydraulic Cylinder Failure and Repair Costs
- Video about What Is The Formula For Surface Area Of A Cylinder
- Question about What Is The Formula For Surface Area Of A Cylinder
- Rate Articles What Is The Formula For Surface Area Of A Cylinder
- Search keywords What Is The Formula For Surface Area Of A Cylinder

## 4 Ways to Minimize Hydraulic Cylinder Failure and Repair Costs

As a product group, hydraulic cylinders are almost as common as pumps and motors combined. So if you operate a lot of hydraulic equipment, it’s likely that cylinder repair expense is a significant portion of your total operating costs.

According to some studies, up to 25% of mechanical equipment failures are failures of design. If we apply this to hydraulic cylinders, then as many as one in four hydraulic cylinders are not adequately designed for the application they’re operating in.

This doesn’t mean that the cylinder won’t do the job asked of it, it will – but not with an acceptable service life. So if you have any cylinders that don’t last like they should you may need to address one or more of the following four issues:

#1. Bent Rods

Bending of cylinder rods can be caused by insufficient rod diameter or material strength, improper cylinder mounting arrangement or a combination of all three. Once the rod bends, deforming load is placed on the rod-seal. This increases leakage and ultimately results in premature failure of the seal.

The allowable rod loading for a cylinder in an existing application can be checked using the Euler formula.

#2. Rod Finish

The surface finish of the cylinder rod has a significant effect on the life of the rod seal. If the surface roughness is too low (smooth), seal life can be reduced as a result of inadequate lubrication. If the surface roughness is too high, contaminant ingression is increased and an unacceptable level of leakage past the rod seal can result.

In the context of extending cylinder service life, think of the cylinder rod’s surface as a lubricated, wear-surface and treat it accordingly.

In some applications, the use of an alternative rod surface treatment with superior mechanical properties to conventional hard-chrome plating, such as nickel-chrome plating or High Velocity Oxygen Fuel (HVOF) metal spraying, can increase the service life of the rod and its seals.

And in some cases, the installation of a shroud or bellows to protect the rod surface and its seals from impact damage and contaminants, can afford similar life extension benefits.

#3. Ballooned Tubes

Ballooning of the cylinder tube is usually caused by insufficient wall thickness and/or material strength for the cylinder’s operating pressure. Once the tube balloons, the correct tolerance between the piston seal and tube wall is lost, allowing high-pressure fluid to bypass the seal. This high velocity fluid can erode the seal and localised heating caused by the pressure drop across the piston reduces seal life-the end result of which is: premature failure of the piston seal.

#4. Insufficient Bearing Area

If the surface area of the bearing (wear) bands in the gland and on the piston are insufficient to adequately support the side thrust transferred to the cylinder, excessive load is placed on the rod and piston seals. This results in deformation of the seals, and ultimately, their premature failure.

Repair or Redesign?

To summarize the above: not all hydraulic cylinders are made equal. So if you have any hydraulic cylinders that suffer recurring failure, it’s likely that design modifications are required to break the vicious circle of failure and repair.

## Video about What Is The Formula For Surface Area Of A Cylinder

You can see more content about **What Is The Formula For Surface Area Of A Cylinder** on our youtube channel: Click Here

## Question about What Is The Formula For Surface Area Of A Cylinder

If you have any questions about **What Is The Formula For Surface Area Of A Cylinder**, please let us know, all your questions or suggestions will help us improve in the following articles!

The article **What Is The Formula For Surface Area Of A Cylinder** was compiled by me and my team from many sources. If you find the article What Is The Formula For Surface Area Of A Cylinder helpful to you, please support the team Like or Share!

## Rate Articles What Is The Formula For Surface Area Of A Cylinder

**Rate:** 4-5 stars

**Ratings:** 2716

**Views:** 40738430

## Search keywords What Is The Formula For Surface Area Of A Cylinder

What Is The Formula For Surface Area Of A Cylinder

way What Is The Formula For Surface Area Of A Cylinder

tutorial What Is The Formula For Surface Area Of A Cylinder

What Is The Formula For Surface Area Of A Cylinder free

#Ways #Minimize #Hydraulic #Cylinder #Failure #Repair #Costs

Source: https://ezinearticles.com/?4-Ways-to-Minimize-Hydraulic-Cylinder-Failure-and-Repair-Costs&id=7732218